This section will help you plan all the artificial grass and materials you will need to complete your project.
OK! You’re probably wondering how you install artificial grass as your feed up of looking at a patchy, worn-out old lawn with a broad swathe of beautifully lush Namgrass artificial grass. That’s great. Now, whether you handle this as a DIY project or you get someone in, careful planning and preparation will pay off handsomely in the end. Spending time on basics like a smooth, level surface is important if you are going to get a result to be proud of. The below instructions are our recommended installation process for laying Namgrass artificial turf. There are other ways to install which can be dependant on materials available and ground conditions but do give us a call if you’re unsure. Let’s get started!
Watch install video
First you need to remove all the old turf. If you have an area larger than a few square metres, it’s worth hiring a turf cutter. It will make the job much quicker and easier and it helps take the hassle out of achieving a level surface.
To enhance its good looks for years to come, Namgrass should have neat, durable edge around it. When choosing which material to use (timber, metal, concrete or brick) remember Namgrass is available in pile heights from 16mm to 38mm deep, so you should lay the height of your edge accordingly. Next, have a nice cup of tea.
Once the edge is in place, the entire area needs to be covered with a layer of Type1. Although the depths can vary due to condition and use of the area, a typical base will consist of between 50-70mm of Type1 aggregate and a 20mm top layer of compacted and levelled Grano dust also known as ‘Fine Type 1’ which has particles no bigger than 5mm.
Your local builders merchant will be able to advise and supply on materials. Take along your measurements, including the depth, so they can calculate the quantity.
Next, another trip to the hire shop for a compacter which is needed to compress the material and provide a firm base. Depending on which Namgrass you choose, keep the base layer roughly 20mm below the top of your edging. Remember to form a slight camber so the base slopes towards the edges, this will help accommodate any settlement over time.
It’s a good idea to spray the area with water to keep the dust down and help the aggregate to bind. Then it’s time for another cup of tea. Finally, (phew!) cover the base layer with a weed membrane, pinning it close up to the edging.
Come on, come on, back to work. Carefully cut the overlapping edges, sharp knife essential, so they fit snugly up to your edging.
Whilst it’s not essential, some high use areas, such as family gardens, benefit from an even layer of kiln dried sand infill – approx. 5 kilos/m². This provides additional stability and weight to the product, thus making for a much nicer completed project. After spreading the sand, brush up the grass to lift the pile and settle the sand in. More tea.
If you are a pet owner we suggest not infilling with sand to ensure a lawn that smells fresher for longer.
Depending on the size and shape of your garden you may well need to join Two sections together. Our top tip here is to take your time. To make sure you get a professional finish, follow these simple instructions.
Line up the two lengths ensuring the pile runs in the same direction. Fold back the edges of the first length and locate the third and fourth rows of stitching. Using a sharp knife (change the blade it will be blunt by now), cut through the latex, between the rows of stitching, all the way along. Take care not to cut the blades of grass. Remove the excess strips and repeat the process on the other length. Time for tea, and have a Hob-Nob too, you’ve earned it.
Line up the cut lengths and fold back the edges, holding them back all along the join. Roll out the joining tape, shiny side down, on the ground between the two lengths of Namgrass. Use a cartridge gun (and spreader if you like) to apply the adhesive evenly along the tape. Starting at one end, fold the two lengths of Namgrass back over so they stick to the tape. Take care not to get grass fibres stuck in the glue. Not long now, think of all the grass cutting you won’t have to do! Once both edges are folded over, walk gently along the joint to firm it down. If you can see the join, make small adjustments until it disappears. Leave at least two hours for the glue to go off, or up to a day if it is below freezing.
Well done! Celebrate by selling your old lawn mower and opening a bottle of bubbly!
Find a list of some of the more common asked questions that you might find useful.
10 year warranty
European Manufacture
Extensive product range
Delivery in 3-4 days
This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.
Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.
If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.
This website uses Google Analytics to collect anonymous information such as the number of visitors to the site, and the most popular pages.
Keeping this cookie enabled helps us to improve our website.
Please enable Strictly Necessary Cookies first so that we can save your preferences!
